Installation Guide
Take your time, follow each step carefully, and enjoy a clean, professional-looking finish.
Our accessories are designed specifically for AYN THOR. For the best result, install them in a clean, well-lit space and avoid rushing the process.
Before You Begin
Before installation, turn off your AYN THOR and make sure the surface is completely clean, dry and free from dust, oil and fingerprints.
Work in a clean, well-lit environment and carefully check the position of every piece before applying firm pressure.
Turn Off the Device
Clean the Surface
Work in Good Lighting
Take Your Time
How to Install Your AYN THOR Skin
Align each piece carefully before applying firm pressure.
Clean the Device
Use a microfiber cloth or alcohol wipe to remove dust, fingerprints and oil from the device. Allow the surface to dry completely before continuing.
Check the Pieces
Before removing the backing, compare each skin piece with the matching area of the device. Check the buttons, ports, vents, speakers and edges carefully.
Align Before Applying
Peel back only a small section of the backing. Align the skin with the buttons, openings and edges before pressing it onto the device. Do not remove the entire backing at once.
Apply Slowly
Press the skin down gradually while peeling away the backing. Smooth it from the center toward the edges to reduce air bubbles and wrinkles.
Reposition if Needed
If the skin is not aligned correctly and has not been pressed down firmly, carefully lift it and reposition it. Do not pull too hard or stretch the material.
Finish the Edges
Press carefully around the edges, corners and curved areas. For difficult curved areas, use a hair dryer on a low heat setting for a few seconds to gently soften the material. Keep the hair dryer at a safe distance and never overheat the device.
How to Install the Dual-Screen Protectors
Each set includes protection for both the upper and lower AYN THOR displays. Install one screen protector at a time.
Clean Both Screens
Use the included cleaning tools or a microfiber cloth to remove dust, fingerprints and oil. Make sure no dust remains before installation.
Check the Position
Place the protector above the screen without removing the backing. Confirm the correct position, orientation and edge alignment.
Remove Dust
Use a dust-removal sticker to remove any remaining particles. Even a small piece of dust may create a visible bubble.
Align and Apply
Peel away part of the protective backing and carefully align the screen protector with the display. Lower it slowly onto the screen.
Remove Air Bubbles
Gently press from the center toward the edges using a soft cloth or application card. Small air bubbles caused by air can usually be pushed toward the edge.
Repeat for the Second Screen
After completing the first screen, repeat the same process for the second display.
Helpful Tips
Common Installation Issues
If something does not look right, stop and check before continuing.
The skin is not aligned correctly
If the skin has not been pressed down firmly, carefully lift it from the nearest edge and reposition it. Avoid stretching the material.
Small bubbles appeared under the skin
Gently smooth the skin from the center toward the nearest edge. Do not puncture the skin with a sharp object.
There is dust under the screen protector
Carefully lift the nearest corner using a piece of tape. Use a dust-removal sticker to remove the particle, then lower the protector again.
The edge will not stay down
Make sure the surface is clean and dry. For curved areas, use a small amount of low heat and press the edge gently for several seconds.
I damaged the product during installation
Stop the installation and contact our support team with clear photos of the problem. We will review the situation and help you find the best available solution.
Need Help With Installation?
If you are unsure about any step or run into a problem during installation, please stop and contact us before continuing. Send us your order number together with clear photos of the product and the installation area. Our support team will review the issue and guide you through the next steps.
Final Reminder
Installation results depend on careful preparation, alignment and application. Please read the instructions before starting and contact us if you are unsure about any step.
- The AYN THOR console is not included.
- Product appearance may vary slightly depending on the selected design.
- Installation-related damage caused by stretching, excessive heat, dust or incorrect alignment is not automatically considered a product defect.